![]() The device was tested with PipeWire, PulseAudio performance was not tested. Playback works near flawlessly out of the box, the only issue is the occasional (non-frequent) crackling noise, but this issue occurs on windows as well so it is not a Linux or ALSA specific issue. The solution to the problems with GPU performance modes not properly changing when switching between battery and AC power is to log out of your x session or restart Xorg. If you boot on AC power then unplug your laptop and run on battery, the GPU will try to perform as if it were still on AC (this could damage your hardware!) ( bug report).If you boot on battery then plug the laptop into AC, the GPU will still perform as if you are on battery.The integrated GPU works without problems as expected. Stutters a lot when display refresh rate misconfigured (the tested model behaved fine at 240hz(native for that model) and 120hz, but lower (96, 72 and 60) resulted in a great deal of stuttering on the display) This is a common problem (not unique to this hardware) The dedicated graphics are multiplexed and should work well for VGA pass-through, as well as just behave generally better than non-multiplexed GPUs. If you have the same display as the tested model this color profile might work for you. The main problem is that the color temperature in the default profile you will get on Linux from the EDID will be configured for 5000k when it should be 6500k as is standard. The default color profile you will get for the display may be wrong thus displaying colors incorrectly (this happened on the tested model), to get a correct color profile you can boot into windows and extract the color profile from there. You can undervolt via the amdctl AUR utility, it is recommended to only do so in small increments (e.g. Like with many laptop models, these models seem to be designed to run your CPU at a steamy 90+☌ when under load, as such thermals (and therefore performance) may be improved with undervolting. It is not yet confirmed if this resolved the issue for this laptop. ![]() On 7 August 2023 a decision was made to disable random number generation on fTPM for all AMD fTPM users to combat this issue on kernel 6.5 and also on the next updates to other stable kernels 6.1 and newer.Kernel 6.3 was supposed to have a hotfix for this issue, but it does not seem to work for this model.But unfortunately sometimes motherboard device page is failing and the only solution here is restart computer multiple times to make the device page available again. I discovered that above mentioned strips have 24 leds and setting them in LastProfile.xml file making Armoury Crate work as expected. Armoury Crate found this device as gen1 and set default led count to 120. My current configuration have two "ARGB headers from EK-Quantum Vector² Strix/TUF RTX 4090 D-RGB ABP Set - Nickel + Plexi". I discovered that the issue is coming from LightingService. There's an error with the device page.The application is going to reload the device page now". After installation the device page for my motherboard is works great but after an hour the page reports the error below. Hi, I installed Armoury Crate and looks like there is an issue with discovering my motherboard. I have to go to the taskmanager to restart the already running Armour圜rateService in the Secive tab then its runs fine for a few minutes then i have to do this again. When i start a game or so it works fine for about 30 - 40 minutes then its dark. If having issues, check if all updates are installed. Under Advanced effects, enable In-Game lighting effects Go to the Aura Sync page, and select AURA effects tab. Then Update Center, and click on Check for Updatesįor games supporting Aura Sync, in-game lighting effects can be enabled easily: *System specs, internet speed, and Windows background process settings will determine the time needed for updates. If there are, do no open Armoury Crate and wait for 15-20 min after a reboot while updates are installed. If this is your first time installing Armoury Crate, updating all essential files will take some time and requires you to restart your system.Īfter restarting your system, Armoury Crate updates in the background if necessary. Suggest to uninstall Aura Sync software if already installed.ĭownload and install Armoury Crate from the link below:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |